Adhesives & Sealants
RTV-1 & RTV-2
Agriculture Advajunts
Artificial Marble / Quartz
Building Protection
Coatings & Paints
Contact Lenses
Dental Surgery
Diffusion Pump Fluid
Fillers & Pigments
Foundry Investment Casting
Foundry Resins
Glass Fiber
Li-ion Batteries
Olefin Polymerisation
Personal Care
Photovolatics (Solar Cells)
Plastics & Thermoplastics
Polyurethane Foam
Rubber & Tyre
Silicone Rubber
Condensation Cure
Addition Cure
Heat Cure Elastomer
Sol-gel Coating
Textile Finishes

Silanes & Silicones for Coatings & Paints
  Silanes as adhesion promoters Silanes as dispersion aids for fillers and pigments
  How to use a silane adhesion promoter? Polyester modified silicone leveling agent
  Suggested adhesion promoters Reactive silicones
  Silanes as crosslinkers Substrate wetting agent
  Silanes as curing agents (hardeners) Defoamer
  Silanes Selection Decision Tree Anti-graffiti and easy-clean additives

How to use a Silane Adhesion Promoter?
The silanes can be blended into an adhesive formulation or used as primers on substrates. The structure and reactivity of the silane will affect the ability of the silane to migrate. The most effective way to promote adhesion is to apply the silane as a primer to the surface, followed by the coating. In this way, the silane will be on the surface and therefore at the interface where it can enhance adhesion between the polymer and the substrate. Silane primers are usually dilute solutions of 0.5 to 5 percent silane in alcohol or water/alcohol solvent. They are wiped or sprayed on the substrate, after which the solvent is allowed to evaporate. While the concentration needed for a specific application may vary, one percent (1%) based on resin content is recommended as a good starting point. The primer must dry completely before applying the coating.
As Primer
Pretreat substrate with silane.  Very efficient use of silane for adhesion promotion, not efficient resin crosslinking (minimal stability problem), two step process. [Method]
Primer Application Method
Dissolve 0.5-5.0 weight percent silane in a compatible, volatile solvent (or mixture).
  Alcohols are most commonly used, for water compatibility.
Equal parts water (based on silane) may be added to prehydrolyze silane if water is compatible with the solvent.
  If primer is to be used immediately, the solution may be acidified.
Apply to clean, grease-free surface.
  Wiping, spraying, brushing, dipping
  Film thickness < 0.1 mil
Solvent removal by drying at 50-60°C for 10 min.
Protect surface from contamination and coat within 24 hr.

Integral Blend
Mix silane into coating formulation.  Much better for crosslinking, also good for adhesion promotion. Possible silane hydrolysis and condensation on storage. Most customers will do it this way. [Method]]
Integral Blend Method
0.5-2% Silane added to polymer matrix prior to application
Silane may be “soaked into” some polymers
Pot life depends on
  a. moisture content of matrix polymer
  b. reactivity of silane to matrix polymer
Silane may be added at compounding stage, e.g. liquid silane pumped into extruder mixing zone

SiSiB® Silicones for Textile SiSiB® SILANE DONORS
SiSiB® Silicones Water Repellents SiSiB® Silicones for Personal Care
SiSiB® Silicone PU Additives SiSiB® Silicone Coating Additives
SiSiB® Silicone Masterbatch for Plastic SiSiB® STP (Silane Terminated Polymer)
SiSiB® Silane Crosslinkers SiSiB® Silane Coupling Agents